Ap.setup - Wireless Range Extender Configuration Using 192.168.10.1

What you Want to Setup For?

What is ap.setup?

Trying to setup your wireless range extender? using http://ap.setup you can make login to your dodocool, wavlink,comfast extenders. Before going to access, you need to ensure your device is connected with a repeater network. The default IP Address 192.168.10.1 is the key to open the administration panel. Or you can also use the WPS button to configure your repeater.

Access point configuration using ap.setup

Ap.setup is a redirection that will redirect you to the login portal. It works offline and only can be accessed using the wavlink extender network. Many wireless routers allow you to connect using wireless access point (AP) and wireless extender in order to increase the wireless range of your extender. Please note that your extender will lose all functions like port forwarding or DHCP server after becoming an access point. You can easily configure the mentioned extender’s using ap.setup. To complete configuration follow the steps :

Power on your extender via connecting it’s power cable into a working electrical outlet. Wait for sometime until the LED indicators turn into solid green.
Enable the WPS connection by pushing the small button on your router and extender too. (Connect within 2 minutes).
When the indicator turns into solid green, That means the extender is successfully establishing a connection with your wireless router.

Wireless access point setup using http://ap.setup

To set up your extenders using wireless mode. Connect an ethernet cable with your extender to the router. Then connect your device with the extender network. In this way, you can easily access it. Follow some simple methods to access ap.setup admin login panel.

Connect your wireless extender near to the router by plugging the power cord into an electrical outlet.
Take an ethernet cable and connect one end with the router ethernet port and another with a wireless extender port.
Use a computer to access the ap.setup offline page. Enter the login credentials to enter the admin control center.
After login, you can configure your extender easily by following the ap.setup wizard instructions.

How to set up a Ubiquiti access point?

Installation process of ubiquiti access point is complex for the new user’s by reading the manual instructions. Follow the methods step by step :

Unpack the access point and take the network cable as well as power cord for the access point.
Connect 1 end of the network cable into the access point and another end in the modem(router).
Now power on the device by connecting the power adapter to the power source.

Now the access point is working, Let’s go to install the software. That is used to configure the access

After installing the software, open the web browser. You will automatically redirect to the access point configuration portal.
Click to advance option and then select “localhost”.
Select your location and set a timezone. Complete all your basic settings according to your preferences.
Open network settings, Here you will get a list of all nearby active networks. Click on the device name which you want to configure.
In the next step, You need to choose an SSID and input the password for your wireless network. Click next after entering it.
Now, You have to choose a login username or password for the admin account.
A new settings overview page will open on your computer screen, review settings and click to finish once done.
Automatically you will land on the Ubiquiti admin login page. Enter the login details that you created earlier to log in with your Ubiquiti account.

Cisco ap configuration

The installation of cisco access point is confusing. It may be hard to set up for new user’s by using the manual instructions so follow the given steps :

First ensure that your PC which you are going to use is configured properly and obtain the IP address automatically. Or manually assigned an IP address by using the same subnet as AP.
Now connect your computer to the power injector. Insert the network cable into Category 5 Ethernet cable.
Use coaxial cables to connect the power injector with the access point.

If you are facing any error or make any mistake, Perform a reset and configure it with basic settings. In this way, you can easily configure your cisco access point.

Rogue access point configuration

Rogue access points work like a mesh network. Multiple devices can get connected at one time without any speed interruptions, The configuration process is simple but confusing. So let’s come to configure :

Access your wireless device web based setup portal. By using the default IP address.
In the management portal. Open the configuration tab and click to wireless. Then select Rogue AP detection.
A new page will open, Here select your desired radio from the list : radio 1, radio 2, or 5ghz frequency.
Enable it on Rogue AP detection.
In the detected rogue ap list choose your access points and click to “TRUST” and the selected will place on the trusted ap list.

Netgear ap setup

In order to use netgear wireless router as ap mode. You need to configure the settings. By using an access point a number of devices can connect using a mesh network. But during using your netgear router access point it will lose all the features of the router. Follow the given steps:

Simply launch any web browser in your NETGEAR router network connected device.
Enter the login credentials to make login.

NOTE – You can use “ADMIN” as a default login password and username.

After login. Click the “ADVANCED” option.
Now select the wireless access point in the next step.
Enable AP mode. And click to apply

In this way you can easily complete netgear access point configuration.

Ruckus access point configuration

Power on your ruckus ap device by connecting it to the power source and connect an ethernet cable with your computer/laptop to access the login interface :

Insert the power cable in the working electric socket and switch “ON” your ruckus access point.
Connect your computer/laptop with the device network using the default passkey. (Printed on the label at the backside)

You can directly connect your mobile/desktop using an ethernet cable to the ruckus access point.
Open any web browser, In the same device and at the top URL box type the default IP address https://192.168.0.1 and go for it. If not opening then you can use http//10.0.2.3.

A new login interface will appear on your computer screen. Enter “ADMIN” in both fields. To login.
On the system bar tap on IP settings. Enable gateway mode and manually enter all the details.
Click to apply.

In this way you can easily do ruckus ap setup.

Meraki access point configuration

In order to access the meraki access point login portal. Connect your device with the meraki network.
Type 10.128. 128.128 in the URl box. On the login interface type “ADMIN” in the username box and in password enter the serial number of the device.
On the admin center navigate wireless then select configure >Access point.
List of SSID will appear on your screen, Select the guest network.
A “Association requirements” tab will appear on screen.

Select “OPEN” no encryption.
For the splash page click to “NONE”.
Now open the “addressing traffic section”.
Click to “use Meraki DHCP.
Now click to apply to save all the changed settings.

In this way you can easily complete a Meraki ap setup without any Hussle.

Wavlink extender configuration using ap.setup | WPS Setup

Configuring a wavlink extender is a very simple process. By using the WPS button you can easily connect your extender to the existing Wi-Fi network.

Follow the given steps:

Turn on your wavlink extender by plugging the power adapter into a working electrical outlet. Be sure your extender is in the range of modem or router.
When the LED indicator turns into solid green, Simply enable the WPS button of your wavlink extender.
Using the same way, push your router WPS button, Greenlight will appear on both devices. That means searching for WPS active devices.
Within 2 minutes your router and extender sync with each other.

In this way you can easily complete the wavlink extender setup using ap.setup wavlink.

Opticover Wi-Fi Extender Configuration

Opticover wifi extender is a better device than other networking extenders. If your home has lots of dead zones and you are not getting range according to your need. In this case, you can use an Opticover extender. So let’s for Opticover ap setup. Here are some simple steps that can help you:

Connect your extender to an electrical outlet and ensure the power button is turned “ON”.
Turn On your access point by sliding the power switch. Now, connect your Opticover extender with an internet router using an ethernet cable.
Connect your device with Opticover default network – “WIRELESS N” Wi-Fi Network. Or can also connect your computer to the extender directly with a LAN cable.
Navigate any web browser in your exact device and in the URL box go for Opticover default ip: 192.168.188.1 or ap.setup. A login page will appear on your computer screen.

On the login screen, it will ask to enter the password. The optic over extender default password: admin.
After login, A new optic over extender setup page will appear, here select Oticover setup wizard and then customize the access point settings by following instructions.
After doing all the changes, please reboot your device.

Now your Opticover extender is ready for work as an access point. Note the LED indicators, it will turn solid greens which means your extender is ready and you can connect your devices.

Coredy wifi extender setup with ap setup

With Coredy wifi extender say bye-bye to all dead zones areas in your house. The Dual-band frequencies of this extender provide a strong signal with an ultra-fast boost network. The Coredy extender login is important to configure the settings. So here we are going for Coredy extender setup using http://ap.setup.

Turn On your Coredy wi-fi repeater to configure the settings.
After turning On your extender, please connect it with your internet modem by connecting an ethernet cable to both device WAN ports.
After establishing the connection successfully, Please connect your computer to Coredy extender EXT wifi.
In any web browser type http:// ap.setup and search for it.
You will enter to the Coredy wifi extender setup portal, hereafter login you can manage the settings.
On the Coredy admin panel, Click to settings and select access point mode configure the settings by following the on-screen instructions.

So Coredy wifi range extender setup will be complete easily just by using these explained steps.

Dodocool wifi repeater setup by accessing http ap.setup | 192.168.10.1

Dodocool wireless repeater is the best device that can increase the signal strength of your wireless router. The MU-MIMO technology provides an excellent performance to your networking devices, You can easily access the Dodocool wifi repeater login portal by accessing http://ap.setup login page. But be sure in which device you are trying to access is need to connect with the Dodocool wifi booster. Follow the given steps:

Connect your extender into the electrical outlet and wait for the green light indicator.
Open Wi-Fi settings in your device and connect with Dodocool wifi extender network ( Wireless-N).
Open any default browser and in address bar hit 192.168.10.1 or ap setup click enter.
Instantly Dodocool wi-fi extender login page appears on your computer screen.
Enter Dodocool repeater default password and username: “admin’.
Click to login, you will directly redirect to the Dodocool wifi extender setup page.

On the next page, select your connection type and connect your extender with your home router WI-FI network using a password.
After connecting wait for 35 seconds and click to apply. Your device will reboot automatically.
Now connect your devices with the extender network, In the Wi-Fi list, the SSID will appear the same as your router network name. Only the last three digits will change for example Mynetwork_EXT.
You can change the network name on the extender admin setting page, and you are able to use the extender network.

Victony wifi extender configuration using ap setup login

The victony dual-band wifi extender is very helpful in big houses or large offices. If there is any dead zones issues. You can easily get rid of them by using this extender. It will increase the range area by covering all the weak network zone. This extender has multiple features and is equipped with MU-MIMO technology with 4-gigabit ethernet ports for high-speed connection. The victony extender login can be easily accessed using ap.setup configuration page. So let’s come to edit extender settings.

The first step is to Plugin your victony wifi extender into the nearest electric socket to your home router.
After connecting to electricity. Please note the LED indicator is turned into a solid color.
In your laptop, mobile open WI-FI manager and connect with victory extender network. (Maybe the network appears unsecured).
After connecting your device with victony extender. Launch any web browser and at the top in address bar type ap.setup or 192.168.10.1. (We recommend you to please copy http://ap.setup this URL to avoid mistakes).

Then wait, victony extender login page will appear in front of you.
On the login page, enter victony extender default password and username: “admin”.
Click to login, you will redirect to victony extender setup wizard page.
Select your connection type. Then connect your extender with the home router network by selecting SSID and using the network key.
The victony wifi extender setup is finished. You can also access the internet after connecting your device to victony wifi network.

MSRM WiFi Extender Setup - ap.setup | 192.168.10.1

The MSRM wifi extender is an ideal choice to extend the home network in your house. MSRM wifi extender is a small, elegant and wall-mounted device. This extender also has a powerful performance and boost home network in a wide area. If you have range issues in your house and your network keeps disconnecting. Just place your extender between your router and dead zone area. It will convert weak signals to a strong network as well as makes your house full of the network. So let’s proceed with how to configure the MSRM wifi extender.

Plugin your extender into an electric outlet near your home router.
Open the Wi-Fi menu on your laptop/mobile and connect with the MSRM_EXT network.
Launch default web browser in the same device as well as type ap.setup or 192.168.10.1 and go for it.

You will redirect to msrm extender login page. Here in the credentials box enter MSRM extender default password and username: “admin”.
Click to login, msrm setup wizard page will appear.
On the main screen, select connection type : repeater mode.

Select your Wi-Fi network which you want to extend from the given list.
Connect with the network using network password.
You can also create a new network name if you want otherwise it will automatically copy your home router SSID name.
The network password will remain same as your router WI-Fi password.
Connect your extender with home router network and your extender is ready to use.
Also, connect client devices to extender network and MSRM wifi extender setup is done.

Galaway Wi-Fi Extender Configuration Using http //ap.setup galaway

Galaway wireless range extender login can only be accessed using http://ap.setup or Galaway extender default Ip. To manage the extender settings and edit wifi network login page must require. The Galaway extender is a dual-band networking device. It covers all the weak zones of your house but you just need to configure Galaway extender correctly. So follow these steps.

Turn on your Galaway extender near the wireless router.
Connect your laptop or any device with Galaway extender network using a wireless method as well as ethernet cable.
After successfully connecting your device with the extender network. Open any web browser on your same laptop or any network-connected device.
At the URL box, hit http://ap.setup and click to search.
Galaway wifi extender login page appears on your screen.

Enter Galaway default password or username “admin”.
On the main home page, Select connection type repeater mode.
Connect your extender with your home network which you want to extend.
You also need to enter the network security key for connecting your extender.
If you want to change the extender SSID name please input a new name and also select a password. Otherwise, you can also skip.

Keep in mind- If you will not change the extender SSID and password. The network name will same as the router SSID. To identify network notice last three digits of SSID will be like Existingnetwork_EXT.

Connect your devices to this network and Galaway wifi extender setup is complete. You can enjoy the internet.

Please note, While configuring any extender settings or setting up. Your need to access the login page. It’s difficult to remind the complicated IP Address of each device to log in. So you can use the ap.setup to directly access the login page.

Why does ap.setup not working?

Ap.setup is a page that is accessible without using the internet. But there is one condition, your device must need to connect with the same extender network. Hence, we know all different extender’s login pages can be accessed by their default IP address. Every extender has different IP, some local brands use the same. In the same way http://ap.setup can only access after connecting to Wavlink, opticover, Coredy, vicotony, Dodocool, Lteriver, motoraux, cudy, Galaway, glamorance, wireless access point, Ubiquiti, UWSP , Aumifi , rogue, Netgear, ruckus, Meraki, cisco, Aruba, FedEx, google wifi, etc.

In case the web address not accessed can follow these ap.setup troubleshooting

Your device requires to connect with the extender network while accessing http://ap.setup offline page.
Ensure your extender network is stable and your device is in the range.
Check your web browser, if it’s not compatible to open ap setup login page. Try to access in any other web browser or device.
Use an updated web browser. Clear all the web history, cache, cookies and try again.
Check you are typing correctly instead of using a web address. Use extender default Ip to login.
Check your extender firmware is not corrupted.
Reboot your extender and try to access again.